FILTER
Truck mounted, 2007 Haybuster 1150 with Remote Control. No magnet. C15 Cat w/ recent engine work (14,000 hrs). New Parts at 13,000 hrs. Transfluid Coupler rebuild (11k hours). Mill has 2,200 hours and hammers have 180 hours. Updated hydraulics. New belts on both Conveyors. Updated LED lights Truck info: 1996 KW T600 with Detroit Engine 430 HP. 10 Speed (Rebuilt 2023) New Clutch … Continue reading “2007 Haybuster 1150”
Owned it for more than 10 years. Engine rebuilt around 400 hours ago. Unsure of total frame hours. New clutch. Governor works as it should. 24 heavy swing hammers with shock spacers. 4-5 screens included. Videos available. Tires are decent but brakes probably don’t work. No magnet.
Come take a look at this 1999 Vermeer tg525L tub grinder. It is equipped with the knuckle boom grapple loader. This machine has a factory rebuilt engine by the CAT dealership. The engine has very low hours, maybe 500. Magnet, manual clutch. Duplex mill is in good shape. Newer stacking belt. Air works in the … Continue reading “1999 Vermeer Tg525L”
Tg400 Tub Grinder in running condition. It’s an old grinder that does grind. Good pin and plate mill. Magnet. Engine was replaced with a used one at some point. Not roadworthy but we’re not asking much for it either. Come and watch it grind.
Used Hesston BP 25 Bale Processor. Grinds the 6′ round bales. Knives just turned over and never used . Rubber flap dishcarge is in good shape. 1,000 rpm PTO. Loading forks/spikes. No leaks. Great piece of equipment. No longer need it. Located in Texas.
Model year is estimated. Good, old style hay grinder. Can grind 6′ round bales. No hydraulics. No computers. All mechanical drive. Winch on the rear conveyor. Everything works. Newer mill and mill bearings. Engine has had a recent overhaul. A lot of updates and used primarily as a back up. Runs great. Lights and brakes … Continue reading “1975 WHO Tub Grinder”
Very straight tub grinder. Great power. Everything works, including tub governor, lights and brakes. Brand new Michelin tires. Magnet. (Chute for head pulley is available) New conveyor belts. Engine and clutch were done less than 200 hours ago. We believe we’re the second owner. New paint. 36 fixed hammers. Hammer shanks and mill rods have … Continue reading “2001 Duratech HD10”
Primarily used for hay. Very little wear. Decent sized swing hammers. This is an HD model so it will handle some wood grinding. Long conveyor. Spent it’s life in a fairly dry climate so the rust isn’t as bad as it might look. Tub floor looks great. Mill should be very good as well. Extra … Continue reading “1993 WHO P1043SHD”
This would have had a chipper attached to the unit as well. It has been removed. 1996 Cummins B5.9-175 5.9 Liter Turbo Diesel Engine, 175hp, Twin Disc Model SP211HP3 Power Takeoff Clutch, Approx. 75” Inside Diameter Steel Tub with Hydraulic Rotate, 22-1/2” Hydraulic Discharge Conveyor, 160 and 102 hours on hour meters (not accurate), tandem … Continue reading “1996 Olathe 818TG”
This is similar to a current model 2015 PTO tub grinder by Jones/Mighty Giant. Hay grinder or regrind wood grinder. Has over the road tires. Long conveyor. Used about five years ago but we needed something more capable. You could add an engine or make sure you have a couple of hundred hp tractor or … Continue reading “2004 Mighty Giant 2012W”
