Other For Sale

Used or Pre-owned grinder support equipment for the wood waste recovery, mulch and recycling industries.

Find the most current list of grinder support equipment available for sale anywhere. You may find a stacking conveyor, trommel screen, star/finger screener, high lift or high tilt, bulk materials bucket, bagger, parts, etc. You will also find new cone screw log splitters. We strive to keep our used equipment listings fresh. Financing and Trucking available.

Please call us if you need a piece of equipment or have grinder support equipment for sale. Jim 330-323-1146

Skid mounted air lift separator for plastics and other light, high-surface area contaminants.  Adjustable fan speed to accommodate most conveyor speeds and sizes. It will even take large plastic bags. Fully self contained. Hardly used in 2017. Like New!  Save thousands. (This is just for the yellow piece of equipment.) Us it on your wood … Continue reading “2016 AirLift AL200D”

Asking Price : 32500
Horsepower : 46
Type : Other

2015 Backers 3 Mal Star Screener (3 Fraction unit),  100 Gallon Fuel Tank, Screen Deck Size 1 48” x 16’ & 48” x 22’.  11 Yard Hopper. 3 Conveyor Belts with Danfoss Drives. Hopper extensions, central lube, reversing engine and hydraulic fans, extended deck for mulch. Air compressor.  Like  New.  Only 500 Hours. Load height … Continue reading “2015 Backers 3-Mal”

Asking Price : 389000
Horsepower : 174
Type : Other

97 Volvo with a 97 Express blower EB 60. 60 yard box does need some work on electronics but it does blow mulch. We’ve used it this year we have blown mulch up to 200 feet with it so far. Seems like everything works on the body and the truck is in good shape. Motor … Continue reading “1997 Express Blower EB60”

Asking Price : 25000
Horsepower :
Type : Other

Electric, stationary grapple/cab. B4 Rating, 600 Cycles. Includes two 50HP electric motors and pumps, hydraulic cooler, joystick controls. Control box (little blue box in the corner) houses many of the components. Has been shortened to reach approximately 21′ (the third boom was removed). The o ring seals in the cab controls need changed again. We … Continue reading “2002 Jonsered 1090 Grapple”

Asking Price : 29000
Horsepower : 100
Type : Other

West Salem vibrating infeed table. 60″ x 30′ with punch plate screen. Screen holes are approximately 3/4″ diameter. Is in very good condition. Fines dump out the long side. Very heavy unit. Ready to run.

Asking Price : 35000
Horsepower : 50
Type : Other

Variable speed knife sharpener. Higher HP knife sharpener by Simonds. 460V 3 phase. Only used for about 2-3 years. 66″x 30″ x 32″ H. Can demo. Ready to go.

Asking Price : 8500
Horsepower : 5
Type : Other

Similar to a Jackson shaving mill. Double Box, slower speed, 4 x 30 HP motors. Was reworked and installed around 2004 (actual year is unknown). Shavings drop down to a Patz barn cleaner, up to a screener, then to a chopper box (17’x8’6″).  460 3 phase. 30″ knives. Soft start and controls included. Demo possible.

Asking Price : 49900
Horsepower : 120
Type : Other

Used Mill (Rotor) from 2002 MC266 Rotochopper. Was used for pallets. Replaced with a raker mill. This is a decent mill and would be good for an older grinder that you didn’t want to use much or just need a reasonable mill to get you going. Does NOT include bearings.

Asking Price : 5900
Horsepower :
Type : Other

This hammer mill was a rebuild direct from Schutte. It is in extremely good condition with only 40 original hours. It comes with an 8′ infeed conveyer, 440 volt soft start and the 75HP Hammermill/Grinder with a 1.5 or 2″ screen.

Asking Price : 20000
Horsepower : 75
Type : Other
Page 1 of 2
1 2
Other Sold